Reviewed by
Jarrett Dottin
Licensed Occupational Therapist dedicated to helping others live their best lives. Certified lymphedema therapist and amazon affiliate who has tested over 1,000 different products. http://About%20JD →
As an Amazon Associate I earn from qualifying purchases. Some links on this site are affiliate links, if you buy though them I may make a commission at no extra cost to you.
Quick Verdict
Two tiers, twelve spools, and a desk that finally stopped launching filament rolls onto the floor. The facka rack is a plain metal shelf that does one job and does it without drama, and at this price that’s the whole pitch.
Buy if you:
- Have spools rolling off the desk and into cable chaos
- Print with a mix of PLA, ABS, TPU, and PETG and want them visible
- Run a Creality, Ender, Prusa, or Anycubic setup with 1kg rolls
- Want desktop storage that doesn’t swallow your whole bench
Skip if you:
- Expect it to feed filament straight into the printer, it’s storage, not a mount
- Need sealed, dry storage, this is open metal with no moisture control
- Own more than 12 spools and hate the idea of a second rack
Clicking takes you to the seller's website. We may earn a small commission if you purchase, at no extra cost to you.
Printer Filament Storage: Stop the Spool Chaos
Loose filament spools are the worst kind of clutter. They roll. They knock things over. They hide the exact color you’re looking for behind five you’re not. The facka 3D Printer Filament Storage Rack is a two-tier metal shelf built to end that, and after loading it up, my bench stopped looking like a spool avalanche. If printer filament storage is the problem you’re solving, this is about as simple a fix as it gets.
It’s not clever. It’s not app-connected. It’s a rack. And that’s the appeal here.
What the facka Rack Actually Is
Two tiers, six spools per tier, twelve total. That’s the headline spec. It’s a metal frame with 4 adjustable legs, 2 fixing ropes, and rubber foot pads underneath so it doesn’t skate around or scratch the desk. Each tier is rated to hold up to 33 lb, so a full row of 1kg rolls isn’t going to bow it.
The adjustable legs matter more than they sound. Not every bench is level, and being able to tweak the feet keeps the whole thing from wobbling when you pull a roll off.
Loading 12 Spools and Seeing My Colors Again
The best part is the visibility. With everything lined up across two rows, I can scan the whole collection in one look instead of digging through a bin. That blue I always lose? Front row now. Grabbing a fresh roll went from a two-minute hunt to a two-second reach.
The rubber foot pads do real work here. Loaded with a stack of 1kg rolls, the rack stays planted when you tug a spool loose. And the fixing ropes let you strap the rows down so a bumped desk doesn’t send anything tumbling. That’s the whole point of the thing, and it delivers on it.
It Stores Filament. It Doesn’t Feed It.
Here’s the catch worth knowing before you buy: this is a storage rack, not a spool holder that feeds into your printer mid-print. The spools sit and wait. You still pull the one you want and mount it to your machine’s own arm or holder. If you were hoping to run filament straight off this rack into an active print, that’s not what it’s built for.
It’s also open metal, so there’s no moisture protection. PLA and PETG sitting out in a humid garage will still drink up moisture over time. For long-term dry storage you’d want sealed bags or a filament dryer alongside it. The rack organizes, it doesn’t seal.
Get it now
facka Filament Storage Rack
Get the best price on Amazon →As an Amazon Associate I earn from qualifying purchases. Some links on this site are affiliate links, if you buy though them I may make a commission at no extra cost to you.
Who Should Grab One of These
If you print regularly and own more than a handful of rolls, this solves the problem the moment you load it, twelve spools off the desk, all facing forward, all findable in one glance. Home offices and garages are the obvious homes, but the real target is anyone who’s ever spent two minutes hunting a specific color through a pile. It fits the common brand ecosystems too: Creality, Ender, Prusa, and Anycubic setups all use spools this rack is sized for, from 200g up to full 1kg rolls.
The person this isn’t for is the printer with two spools and no clutter problem. You don’t need twelve slots for that. This is for the collector whose colors have gotten out of hand.
Comparing It to a Bin or a Shelf
A bin hides everything and makes you dig. A bare shelf is where the rolling problem starts. Sealed bags protect from moisture but are slow to open and impossible to scan at a glance. The rack beats all three on daily access, pull the color you want in two seconds, but it’s dead last on humidity protection, which matters if your workspace is a damp garage.
This rack sits in the middle. It wins on visibility and access, keeps spools locked in place, and takes almost no footprint. Where it loses is moisture control, so it doesn’t replace sealed bags or a proper filament dryer if humidity is your enemy. Pair the rack with sealed bags: rack for daily grabs, bags for anything sitting untouched longer than a week in humid air.
A Few Tips Before You Order
Set the adjustable legs first, before you load anything. Getting the feet level on an uneven bench takes 30 seconds and saves you a wobble later. Use the fixing ropes even if you think you won’t need them, because a bumped desk with 12 loaded rolls is exactly the moment you’ll be glad they’re there. And keep your damp-sensitive materials in bags with desiccant off to the side. The rack is your grab-and-go shelf, not your climate control.
Pros
- 👍 Holds up to 12 spools across 2 tiers, all visible at a glance
- 👍 Stops spools from rolling off the desk with fixing ropes and rubber feet
- 👍 33 lb per tier rating handles a full row of 1kg rolls
- 👍 Adjustable legs keep it steady on uneven benches
- 👍 Fits 200g, 500g, and 1kg spools across PLA, ABS, TPU, and PETG
Cons
- 👎 Storage only, it doesn’t feed filament into the printer
- 👎 Open metal design offers no moisture protection
- 👎 Twelve-spool limit means big collections need a second rack
Frequently Asked Questions
Does it work with all filament brands and printers?
Yes, it’s brand-agnostic. It’s designed for standard 200g, 500g, and 1kg spools used with common Creality, Ender, Prusa, and Anycubic setups, so as long as your rolls are standard sizes they’ll sit fine.
Can I use it as a spool holder to print directly from?
No, it’s a storage rack, not a feed system. You store your rolls here and mount the one you’re using to your printer’s own arm. Think of it as the shelf, not the dispenser.
Will it keep my filament dry?
No, it’s open metal with no seal, so it won’t protect against humidity. For moisture-sensitive materials like PLA or PETG in a damp space, pair it with sealed storage bags and desiccant or a filament dryer.
How much weight can each tier hold?
Up to 33 lb per tier. A full row of six 1kg spools is well within that, so the metal frame won’t sag under a loaded shelf.
Does it come assembled?
It ships with clear setup instructions and the parts you need, including 4 adjustable legs, 2 fixing ropes, and rubber foot pads. Assembly is quick and doesn’t require any special tools.
What if I own more than 12 spools?
You’ll need a second rack or a supplemental storage method. Twelve is the hard cap here, six per tier. Many people run the rack for active colors and bag the overflow.
Will it scratch or slide on my desk?
The rubber foot pads are there to prevent both. They grip the surface so the rack stays put when you pull a spool and protect the desktop underneath from scratches.
Is it worth it for a small hobby setup?
If you own two spools, skip it, you don’t need twelve slots. But the inflection point is roughly five or six rolls: that’s when colors start hiding behind each other and the desk turns into a rolling hazard. Past that point, the rack earns its shelf space on day one.
Get it now
facka Filament Storage Rack
Get the best price on Amazon →As an Amazon Associate I earn from qualifying purchases. Some links on this site are affiliate links, if you buy though them I may make a commission at no extra cost to you.
About the reviewer
Jarrett Dottin
Licensed Occupational Therapist dedicated to helping others live their best lives. Certified lymphedema therapist and amazon affiliate who has tested over 1,000 different products.
